[Oberon] Problems with Adaptec 7890

urs.sonderegger at fhsg.ch urs.sonderegger at fhsg.ch
Wed Apr 9 10:27:40 CEST 2003


Hi Patrik

After consulting some stuff from the oberon list, I found a tip that works
from Pieter Muller.
Now i got a trace on the serial port (TraceMode=4 !):

Aos 22.5.2002
Single-processor
IDE0..1: 14 000001F0 000003F6 ATA: Status ctrl=000001F0 drv=1 lba=268435455
err=
FF stat=FF s=FF m=80 e=00 b=00 ms=1000
IDE2..3: 15 00000170 00000376 ATA: Status ctrl=00000170 drv=1 lba=268435455
err=
FF stat=FF s=FF m=80 e=00 b=00 ms=1000
Bus-master disabled
SCSI - 1.0 / prk
AosAdaptec7 - 0.41 / prk
[00/06/00] Adaptec AIC-7890/1 Ultra2
[00/06/00] irq=15 MemMap=D9800000/80003000
[00/06/00] bus is wide
[00/06/00] SCB = 32
[00/06/00] Sequencer Loaded lines=374
[00/06/00] BusReset
[00/06/00] IntHandler installed, 15
[00/06/00] IntSeqHandle.AwaitingMsg
[00/06/00] IntSeqHandle.RejectMsg

I'll try to get more information and send it to you

Urs


|---------+--------------------------->
|         |           "Patrik Reali"  |
|         |           <reali at acm.org> |
|         |           Sent by:        |
|         |           oberon-admin at inf|
|         |           .ethz.ch        |
|         |                           |
|         |                           |
|         |           08.04.2003 08:25|
|         |           Please respond  |
|         |           to oberon       |
|         |                           |
|---------+--------------------------->
  >----------------------------------------------------------------------------------------------------------------------------|
  |                                                                                                                            |
  |        To:      <oberon at inf.ethz.ch>                                                                                       |
  |        cc:                                                                                                                 |
  |        Subject: Re: [Oberon] Problems with Adaptec 7890                                                                    |
  >----------------------------------------------------------------------------------------------------------------------------|




Hi Christoph,

* have you tried the latest native alpha?
* do the 2.3.6. and 8.12.00 fail with the same error?
* can you please give more informations on the TRAP?

-Patrik

----- Original Message -----
From: "Christoph Stamm" <stamm at inf.ethz.ch>
To: <oberon at inf.ethz.ch>
Sent: Monday, April 07, 2003 10:30 AM
Subject: [Oberon] Problems with Adaptec 7890


> Hello
>
> I'm using a PC with a motherboard embedded Adaptec AHA-2940U2/W SCSI
> disk controller (BIOS version 2.11). I've tried to install the stable
> version of Native Oberon (2.3.6). It failed during disk controller
> configuration with a TRAP 8 (assert).
>
> When I use the beta version of Native Oberon (31.7.00) then it works
> fine, but it fails again with the latest beta version (8.12.00).
>
> Is this problem known?
>
> Christoph Stamm
>
> --
> Oberon at inf.ethz.ch mailing list for ETH Oberon and related systems
> http://www.lists.inf.ethz.ch/mailman/listinfo/oberon
>
--
Oberon at inf.ethz.ch mailing list for ETH Oberon and related systems
http://www.lists.inf.ethz.ch/mailman/listinfo/oberon








More information about the Oberon mailing list